餐饮业安装静电油烟净化设备时，不可避免地会遇到一些小问题，但并非厂家油烟净化器的质量问题，大多是安装和运输过程中因其他或人为原因造成的。要是出了故障，该怎么办？下面是油烟净化器的常见故障及排除方法。
The catering industry will inevitably encounter some small problems when installing electrostatic fume purification equipment, but it is not the quality problem of the manufacturer's fume purifier, which is mostly caused by other or man-made reasons during installation and transportation. What if something goes wrong? The following are the common faults and troubleshooting methods of oil fume purifier.
油烟净化器不能启动。
The fume purifier cannot be started.
1.如电源线接错，请重新接通电源，重新设置保护空气开关，观察高压模块是否正常工作。
1. If the power line is connected incorrectly, please reconnect the power supply, reset the protective air switch, and observe whether the high-voltage module works normally.
2.原因及解决办法：检测电线绝缘损坏或漏电，更换电线。
2. Causes and solutions: check the insulation damage or leakage of wires, and replace the wires.
3.高电压模组内部短路、更换或维修、油烟净化器电源或漏电保护开关的质量问题。
3. Internal short circuit, replacement or maintenance of high-voltage module, quality problems of fume purifier power supply or leakage protection switch.
设备运行时仍然有刺耳的声音，甚有火花。
There are still harsh sounds and even sparks when the equipment is running.
1.检查油烟净化器电压是否过高。电压适时调节(在人员指导下)。左下方的蓝色箭头，由左向小，由右向大。标准安培计显示范围在5-12a之间。
1. Check whether the voltage of the fume purifier is too high. Adjust the voltage in time (under the guidance of professionals). The blue arrow at the bottom left, from left to small, from right to large. The display range of standard ammeter is between 5-12a.
2.检查机箱电场方向是否正确。变化电场的方向，在运动的两边都有电场方向标志。
2. Check whether the electric field direction of the chassis is correct. Change the direction of the electric field, and there are signs of the direction of the electric field on both sides of the movement.
3.检查高低压接线是否符合电场。适当的接线方式是电场的高压区对应高压接线，电场的低压区对应低电压区，高压线对应锯齿板放电，低压线对应吸附板放电。
3. Check whether the high and low voltage wiring conforms to the electric field. The proper wiring method is that the high-voltage area of the electric field corresponds to the high-voltage wiring, the low-voltage area of the electric field corresponds to the low-voltage area, the high-voltage line corresponds to the sawtooth plate discharge, and the low-voltage line corresponds to the adsorption plate discharge.
4.检查电场是否有杂物、极板变形、绝缘材料损坏。电场中的杂质，用手工修复电场吸附板的变形，替换或修复绝缘材料。
4. Check whether there are sundries in the electric field, pole plate deformation and insulation material damage. Remove the impurities in the electric field, manually repair the deformation of the electric field adsorption plate, and replace or repair the insulating material.
5.清洗后电场的湿度太大。风干或风干电场，注意电场内是否有杂物。
5. The humidity of the electric field after cleaning is too high. Air dry or air dry the electric field, and pay attention to whether there are sundries in the electric field.
Jinan lampblack purifier has induction power supply, and the battery works normally, but the equipment has no reaction, and the battery works normally.
1.当出现故障时，检查外箱体是否接地，确保电场电极接触。
1. In case of failure, check whether the outer box is grounded to ensure that the electrode of the electric field contacts.
2.检查电绝缘体或绝缘瓷是否完好，调整电极板接触，确保接触良好。
2. Check whether the electrical insulator or insulating porcelain is in good condition, and adjust the electrode plate contact to ensure good contact.
At the end, it is necessary to remind the precautions: when using the lampblack purifier, we should develop the habit of regular inspection, regular cleaning and regular maintenance, do a good job in daily maintenance, protect the operation of the equipment, and extend the service life of the equipment. Come to our website for more relevant content http://www.1nightescorts.com OK.
上一篇：通风管道的加工要多注意事项
下一篇：厨房排烟的设计与安装事项
