专注通风管道加工·排烟罩

食堂油烟机排烟罩采用不锈钢拉丝工艺，不仅外表美观，还能防腐防锈。饭店厨房排烟罩吸烟内腔采用大空间设计使得油烟杂质的吸收变得更充分，更强油烟吸收率应大于95%。下面济南排烟罩厂家来讲讲食堂油烟机排烟罩制作要求以及安装事项。

The exhaust hood of the canteen range hood adopts stainless steel wire drawing process, which not only has a beautiful appearance, but also can prevent corrosion and rust. The smoke exhaust hood of the hotel kitchen adopts large space design to make the absorption of oil smoke impurities more sufficient, and the stronger oil smoke absorption rate should be greater than 95%. Next, Jinan smoke exhaust hood manufacturer will talk about the manufacturing requirements and installation of the smoke exhaust hood of the canteen range hood.

食堂油烟机排烟罩制作要求

Fabrication requirements for smoke exhaust hood of canteen range hood

1.油网烟罩后封板、前封板、前页、上滑槽与下滑槽所有外露边均压扣边;

1. All exposed edges of the rear sealing plate, front sealing plate, front page, upper chute and sliding chute of the oil screen smoke hood shall be crimped;

2.油网烟罩后封板与前封板连接为分段短焊，其中前封板HL面外露；

2. The connection between the rear sealing plate and the front sealing plate of the oil net smoke hood is a sectional short welding, in which the HL side of the front sealing plate is exposed;

3.油网烟罩前页与油网烟罩前封板连接为分段短焊，焊接面在前封板外露面前页HL面向下，二端烟罩连接口分别向上90度；

3. The connection between the front page of the oil net smoke hood and the front sealing plate of the oil net smoke hood is a sectional short welding, with the welding surface facing down on the HL front page of the exposed front sealing plate, and the connection ports of the two end smoke hoods facing up 90 degrees respectively;

4.油网烟罩二末端的油烟网罩侧封板与后封板、前封板前页为分段短焊，其中同前页的前端（注：尺寸120mm）、后封板去油槽位置为满焊并打磨；

4. The side sealing plate, rear sealing plate and front page of the front sealing plate of the oil smoke screen cover at the two ends of the oil smoke screen cover are short welded by sections, of which the front end (note: the size is 120mm) and the oil removal groove of the rear sealing plate are full welded and polished;

5.烟罩照明灯须有防水功能，导电线要有转悠穿线护管。

5. The smoke cover lamp must have a waterproof function, and the lead wire must have a rotary threading protective tube.

饭店油烟机排烟罩安装方法

Installation method of smoke exhaust hood for hotel range hood

1.油烟网罩现场安装时，在现场拼接的油网烟罩后封板去油槽位置为满焊，其余位置为分段短焊；

1. During the on-site installation of the oil smoke screen cover, the position where the rear sealing plate of the oil smoke screen cover spliced at the site is removed from the oil groove is full welding, and the other positions are short welding in sections;

2.油烟网罩与墙面固定用M8钢膨胀螺丝加不锈钢大垫片，膨胀螺丝外露螺纹需磨去；

2. The lampblack net cover and the wall are fixed with M8 steel expansion screws and large stainless steel gaskets, and the exposed threads of the expansion screws need to be removed;

3.油网烟罩前页同楼板连接件为螺杆全丝或钢丝绳加吊环螺钉、索具螺旋扣；

3. The front page of the oil net smoke hood is the same as the floor connecting piece, which is a screw full wire or steel wire rope with eyebolts and rigging screw buckles;

4.吊装高度：油网烟罩前页下口离地2000mm，油网烟罩后封板去油槽底部离地1900mm；油网烟罩吊装水平精度一般全长在正负10mm。

4. Hoisting height: the lower opening of the front page of the oil mesh hood is 2000mm above the ground, and the bottom of the oil drain of the rear sealing plate of the oil mesh hood is 1900mm above the ground; The hoisting horizontal accuracy of the oil net smoke hood is generally ± 10mm.

食堂油烟机排烟罩制作要求以及安装事项就讲解到这里了，您对此有什么想了解的内容可以随时来我们网站http://www.1nightescorts.com进行咨询！

This is the end of the production requirements and installation of the smoke exhaust hood of the canteen range hood. If you have anything you want to know about it, you can come to our website at any time http://www.1nightescorts.com Consult!