专注通风管道加工·排烟罩

设计要点

Design points

要根据某一系统的某一楼层管道图纸，并标明接口位置。

According to the pipeline drawing of a certain floor of a system, and indicate the interface location.

管道的设计应从起点开始编号，起点一般为接口位置，相同截面规格相同长度的节点应为相同编号，应按顺序编号。为了便于有组织的施工。

The design of pipelines should be numbered from the starting point, which is generally the interface position. Nodes with the same cross-sectional specifications and length should be numbered in the same order. For the convenience of organized construction.

管道的设计应当显示分支吊架的位置，分支吊架的位置间隔和所有材料的规格需要符合后述规格要求和技术规定。

The design of pipelines should display the position of branch hangers, and the spacing of branch hangers and the specifications of all materials should comply with the following specifications and technical regulations.

山东通风管道的设计应优先考虑弯头和内径满足内外同心弯头要求内径长度要求。

The design of ventilation ducts in Shandong should prioritize considering elbows and inner diameters that meet the inner diameter length requirements of concentric elbows.

管道设计应标出弯头位置变径位置管道轴线位置管道底部标高。

The pipeline design should indicate the position of the bend, the position of the pipeline axis, and the elevation of the pipeline bottom.

加工需要注意的问题

Issues to be noted in processing

通风管道加工不能在其内部设置钢筋骨架或钢筋，如果添加会影响管道的质量。

The processing of ventilation ducts cannot have steel reinforcement skeletons or steel bars installed inside, as adding them will affect the quality of the ducts.

加工不能使用c型直角插入和s型插入的连接方式。 对于特殊管道，不能采用卡扣式咬合口。通风管制作完成后，需要用清洗液清洗，达到标准后才能进行密封。

The connection method of C-shaped right angle insertion and S-shaped insertion cannot be used for processing. For special pipelines, snap on bite openings cannot be used. After the production of the ventilation pipe is completed, it needs to be cleaned with cleaning solution to meet the standards before sealing can be carried out.

减少管道加工过程中出现纵向接缝，不能横向接缝，并且管道间隙应按照设计的清洁水平要求用密封剂堵塞，管道板材接缝的密封面应位于通风管道壁的正压侧。山东通风管道加工过程中应采取防腐措施。管道零件需要镀锌。

Reduce the occurrence of longitudinal joints during pipeline processing, instead of transverse joints, and the pipeline gap should be blocked with sealant according to the design cleanliness level requirements. The sealing surface of the pipeline plate joint should be located on the positive pressure side of the ventilation pipeline wall. Anti corrosion measures should be taken during the processing of ventilation pipes in Shandong. Pipeline parts need to be galvanized.

感谢您的阅读，此文的文章来源：山东通风管道加工更多的内容和问题请点击：http://www.1nightescorts.com我们会继续努力的为您提供服务，感谢您的支持！

Thank you for reading. The source of this article is Shandong Ventilation Pipeline Processing. For more information and questions, please click: http://www.1nightescorts.com We will continue to work hard to provide you with services. Thank you for your support!

上一篇：山东通风管道加工：风管加工的工序标准
下一篇：不锈钢烟罩制作产生哪些作用？