各种空调使用中，都需要通风管道部件，它们是配合空调作业，利于空调运行的主要部件。而通风管道在使用中容易发生堵塞，为避免堵塞，在通风管道处理完毕后，我们可以做两点预防，下面
济南通风管道加工厂家为您解答。
In the use of various air conditioners, ventilation pipe components are required, which are the main components to cooperate with air conditioning operation and facilitate the operation of air conditioners. The ventilation pipe is easy to be blocked in use. In order to avoid blocking, we can take two precautions after the ventilation pipe is handled. Now, the ventilation pipe processing factory in Jinan will answer for you.
日常的检查。通风管道加工完成后，我们可以不时地检查一下通风管道的使用情况，当然，在检查时要保证通风管道的通风效果，只有这样，我们才能看通风管道是否有堵塞。如果通风效果不大，或通风效果不强，就应对其进行处理，避免产生更深的堵塞效应。
Daily inspection. After the processing of the ventilation pipe is completed, we can check the use of the ventilation pipe from time to time. Of course, we should ensure the ventilation effect of the ventilation pipe during the inspection. Only in this way can we see whether the ventilation pipe is blocked. If the ventilation effect is not large or strong, it should be treated to avoid deeper blockage effect.
定期进行清洁。值得一提的是，通风管道经过加工处理后，不需要再做任何处理，清洗处理是须的维护工作，它们既能保证这个管道长期使用，又能避免出现堵塞现象。因此说，我们要避免通通风管道堵塞，定期清理通通风管道是非常必要的。
Clean regularly. It is worth mentioning that after processing, the ventilation pipe does not need any further treatment. Cleaning is a necessary maintenance work, which can not only ensure the long-term use of the pipe, but also avoid blockage. Therefore, it is necessary to clean the ventilation pipe regularly to avoid blockage of the ventilation pipe.
空调的正常使用离不开通风管道，而通风管道在加工使用后会出现堵塞现象，对此，我们对其进行日常检查并定期清洗，是避免堵塞现象发生的好办法。
The normal use of the air conditioner can not be separated from the opening of the air duct, and the air duct will be blocked after processing and use. For this, we conduct daily inspection and regular cleaning, which is a good way to avoid blocking.
通风管道加工的过程中应该尽量避免出现纵向接缝，但是不能出现横向接缝。而且通风管道的咬口缝和四角的缝隙处，需要按照设计洁净等级要求，然后还要采用密封胶将其堵严。另外通风管道板材的连接缝的密封面应该设在通风管道壁的正压侧。
The longitudinal joint shall be avoided as far as possible during the processing of ventilation duct, but the transverse joint shall not be allowed. Moreover, the seaming seams and the four corners of the ventilation pipe shall be sealed with sealant according to the design cleanliness level requirements. In addition, the sealing surface of the joint of the ventilation duct plate should be set at the positive pressure side of the ventilation duct wall.
加工的时候，不能在通风管道内部设置加固框或者加固筋，因为这样对于通风管道的质量会造成一定的影响。通风管道加工不能采用S型插条和C型直角插条的连接方式，另外对于一些特殊的通风管道来说，还不能采用按扣式的咬口。
During processing, reinforcing frames or reinforcements cannot be set inside the ventilation ducts, because this will have a certain impact on the quality of the ventilation ducts. The connection mode of S-shaped and C-shaped right angle inserts cannot be used for the processing of ventilation ducts. In addition, snap joint cannot be used for some special ventilation ducts.
Therefore, if you have the operation of processing ventilation pipes, pay more attention to the maintenance and methods to avoid blockage after processing. If you want to know more about lampblack purifier and air purification, please pay attention to us http://www.1nightescorts.com Come on!
上一篇：关于通风管道加工安装时的五个要点
下一篇：油烟净化器具体的安装规范过程
